> Reddit is not centered on user profiles and followers and yet
This is not entirely correct anymore, many of the new features added to Reddit over the last 5 years have focussed on expanding precisely this aspect of the site.
I've been using Mylio on my laptop which might suit you? My main requirement was that I organise photos using my file structure for maximum portability, and this works well with that.
Another options (particularly if your org runs off MS outlook & Teams) - pencil in the review time as an appointment in your calendar, so your status shows as 'Busy' during that time. If that's not sufficient, you can even make it a Teams meeting with only yourself in it, so then your Teams status would show that you're in a call.
Yeah, i use this technique - both a simple blocking appointment as well as a fake meeting with only myself...but what has even happened a few times is that someone will see that i have an appointment or meeting near the end of the day, and they figure they can book a short meeting with me immediately after that block...I have a colleague at work who from about 6pm until the following day blocks his calendar with an "out of office" signal...so its 100% clear that he is off the clock and not available...but still people in this company (from other timezones mostly but sometimes also the same timezone) harass others regardless if a calendar os blcoked, etc...Like i said its simply toxic where i work in this way. But, i appreciate the idea, thanks!
That's not the only version control through - if you use Excel connected to Onedrive or Sharepoint (like most major orgs in my country), then you have version history built-in tracking every edit going back months.
It be worth looking up the I-V curves of solar modules on a datasheet - a key factor is that the maximum power point of a solar module (for a given set of environmental conditions) is really dependent on the voltage that it is running at (whereas the current is more constant based on the light level, up to a certain voltage), so to get the maximum power out the resistance of the load needs to be matched to achieve that maximum power voltage (V_MP).
This is what MPPT controllers do, as this maximum power setpoint will change as environmental conditions change.
> A solar panel's VoC should be its maximum possible output in ideal conditions (open circuit)
I think this is where the confusion arises - what do you mean by ideal conditions? Ideal conditions for solar generation are not necessarily at the same time as the highest voltage operating conditions. VoC tends to be specified at Standard Test Conditions which has light-levels representative of a sunny day (1000 W/m2) and a cell temperature (not ambient) of 25 degrees C, which is already a lot cooler than most panels would typically be at that level of irradiance. So really, the label is already specifying a voltage higher than what you would typically experience during times of max generation.
However, the max voltage could exceed this rating at times when there are cold ambient temperatures with enough light for the module to function, but not enough sun to meaningfully heat the cells. So in this scenario you may have maximum voltage, but you're far from maximum power nor at 'ideal conditions'.
This is information is generally stated on the module datasheets, which specify the Open Circuit Voltage (V_OC) at Standard Test Conditions (STC), and then provide a temperature coefficient for how that voltage changes with temperature.
'Maximum voltage' is very arbitrary as this is directly dependant on the lowest expected operating temperature, hence the industry has landed on stating these values at standardized conditions (STC and NOCT) allowing for direct comparison.
The label on the modules themselves tend to also provide these ratings at STC, e.g. this label from Jinko specifies the Open circuit voltage and also summarizes the conditions assumed for STC:
While I agree that the label could also add the temperature coefficient, I'm not sure if it's reasonable to expect that specialist electrical equipment details all of its operating parameters on an attached label without the expectation of consulting a datasheet or manual. For specific products that primarily target non-specialised consumers however, a different labelling approach may be warranted.
But that's not true - V_OC for PV modules is nearly always spec'd at STC or NOCT, which is clearly stated on module datasheets along with the temperature coefficient of that voltage.
It doesn't matter if it's true. And those spec sheets aren't what you'll find on amazon products. I looked at them, didn't see any mention of temperature. Also, stupid things use XT60 connectors. Not remotely appropriate for 150v DC.
This is not entirely correct anymore, many of the new features added to Reddit over the last 5 years have focussed on expanding precisely this aspect of the site.